Home->PCM for Li-ion/Li-Polymer Battery Packs ->For 11S~13S Packs (40.7V~48.1V)-> For 11S Packs (40.7V)

11S 40.7V Battery Management System (BMS) with RS485, RS232, CANBUS, SMBUS, I2C Communication protocol

Part number: HCX-D328

Features and Benefits

  Programmable BMS With RS485, RS232, CANBUS, SMBUS, I2C Communication protocol (6S~16S)

 
1.Protection Circuit Board for 11S 40.7V Li-ion and Li-Polymer battery pack;
2.PCB applies for 11 configuration Li-ion and Li-Polymer battery pack;
3.To prevent the battery packs from overcharge,overdischarge,over current, over temperature ,short circuit ;
4.With cell balance/equilibrium function;
5.Compatible with all the  Li-ion and Li-Polymer .
6.How balancing function works? after battery pack is fully charged. PCM will detect each cell's voltage and trim higher voltage down until other cells reach the same voltage level. Therefore, it helps cells have longer service life.

Specifications

 

Item

Contents

Criteria

(Adjustable from software/hardware)

1

Model

HCX-D328

6S-16S

Adjustable from software

2

Voltage

Charging voltage

Adjustable from software

3

Current

Maximal continuous charging current

100A (adjustable from hardware)

Maximal continuous discharging current

100A (adjustable from hardware)

Current consumption

≤200μA

 

4

Overcharge Protection

Over charge detection voltage

Adjustable from software

Over charge detection delay time

Adjustable from software

Over charge release voltage

Adjustable from software

5

Over Discharge Protection

Over discharge detection voltage

Adjustable from software

Over discharge detection delay time

Adjustable from software

Over discharge release voltage

Adjustable from software

6

Over Current Protection

Over current detection voltage

Adjustable from software

Over current detection current

Adjustable from software and hardware

Detection delay time

Adjustable from software

Release condition

Adjustable from software

7

Short Circuit Protection

Detection condition

Adjustable from software

Detection delay time

Adjustable from software

Release condition

Cut load, automatically recover

8

Balance

On @ ≥50mV±5mV

OFF @ ≤30mV±5mV

Balance voltage for single cell

Adjustable from software

Balance current for single cell

Adjustable from hardware

9

Resistance

Inner resistance

≤20mΩ

10

Temperature

Single cell temperature when discharge (over temp. protection) ≥65

Adjustable from software

Single cell temperature when discharge (low temp. protection) <-40

Adjustable from software

Single cell temperature when Charge (over temp. protection) ≥50

Adjustable from software

Single cell temperature when Charge (low temp. protection) <0

Adjustable from software

11

Fuel/Gas gauge

Display with 5 LEDs

Thru one button to check capacity

Connection Diagram

 Status and System warning functions:

1)       Push the button on BMS to check the capacity

2)       During Charging, LED will be blinking

3)       Display and warning details:

No.

Working Status

1#

2#

3#

4#

5#

Frequency

For discharging

1

0%--5% Discharge Status

锟斤拷

 

 

 

 

125MS

2

6%--20% Discharge Status

锟斤拷

 

 

 

 

 

3

21%--50% Discharge Status

锟斤拷

锟斤拷

 

 

 

 

4

51%--80% Discharge Status

锟斤拷

锟斤拷

锟斤拷

 

 

 

5

81%--95% Discharge Status

锟斤拷

锟斤拷

锟斤拷

锟斤拷

 

 

6

96%--100% Discharge Status

锟斤拷

锟斤拷

锟斤拷

锟斤拷

锟斤拷

 

For charging

7

0%--20% Charging Status

锟斤拷

 

 

 

 

500MS

8

21%--50% Charging Status

锟斤拷

锟斤拷

 

 

 

 

9

51%--80% Charging Status

锟斤拷

锟斤拷

锟斤拷

 

 

 

10

81%--95% Charging Status

锟斤拷

锟斤拷

锟斤拷

锟斤拷

 

 

11

95%--100% Charging Status

锟斤拷

锟斤拷

锟斤拷

锟斤拷

锟斤拷

 

Note锟斤拷锟斤拷 for LED ON锟斤拷锟斤拷 for LED blinking

 

ON/OFF function (optional)

Signal from the key connected to B+, the output is on, disconnect the signal from the key, output is off

 

(J1 port, K pin, signal from the key to B+)

 

How to connect BMS to PC/laptop to set up all parameters and the communications.

 

 

The communication conventor is an optional product which will not come with products normaly.

 

For engineering study, please send us email for this tool, then we will send you this together with our software drive coming with a USB drive as below:

 

 ·         BesTech Power Software for BMS communication inside

 

·         Specification of the Communication Conventeor inside

 

·         BMS Specification inside

 

·         Battery Connection diagram inside

 

·         BesTech Power Company profile inside

After installed our software to your PC/laptop

The PC-end-software (copyright belongs to BesTech Power) to Set and modifying all the logical parameters

 

 

PCB Layout and size

 

Connections Diagram

 

Copyright © 2011 BesTech Power Co., Ltd.
Tel:+86 - 769 82033052     Fax:+86 - 769 82033050 # 620   E-mail:info@BesTechPower.com
Factory ShenZhen: 3F, Bldg3, Fulian Industrial Park, Heping Industrial area, Jianhui Rd, Longhua, ShenZhen, China 518109.
Factory DongGuan: 3F, Block 1, HaoYun TongYuan Science Park, Qiaojiao Middle Road #1, TangXia Town, DongGuan, China 523726.